YOUARECUTE Builder Gel nr56 15ml

Product detailed description

Key Features

• Acid-free formula.
• Medium consistency, closer to fluid.
• Light caramel pigmentation with a semi-transparent effect.
• Suitable for no-file nail extension techniques.
• Suitable for nail extensions using upper forms.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in cold temperatures and more fluid in warm conditions.
• Thixotropic formula — becomes more fluid as the brush moves through the material during application.
• Can be additionally warmed to make the gel more fluid.
• Hard at a thickness of 1 mm. At a thickness below 1 mm, the material may flex slightly, but this does not affect wear.
• Does not shrink and maintains the nail arch well.
• Must be applied over a Rubber Base.
• Recommended polymerization wavelength: 365–405 nm.
• Recommended UV/LED lamp power: 36–48 W.
• Maximum recommended material thickness: 0.5 mm at the free edge / 1 mm at the apex.
• Full polymerization time: 120 seconds.

Application Method

NAIL STRENGTHENING

1. Removal.

2. Do not file the nail into shape, or leave approximately 2 mm of length that will be removed after leveling.

3. Using a 220-grit file, gently file the surface of the nail without applying strong pressure, lifting the layers of the nail plate. Alternatively, use a 100-grit buffer.

4. Perform the manicure.

5. If removers are used, wash your hands with soap and water after working with them.

6. Degrease the nail using Nail Prep. Apply it in two stages. Use 4 wipes for this process (1 wipe for 5 fingers).
First stage: wipe the nail surface.
Second stage: place a wipe around an orange wood stick and carefully clean the cuticle area and sidewalls.

7. Primer is optional. However, if the base used as the foundation layer has sufficient acidity, primer is not required.

8. It is best to apply the Rubber Base foundation layer with a flat gel brush. Apply the base evenly, carefully working into all sidewalls, and cure in the lamp for 60 seconds.

We recommend not removing the sticky layer from the base, as it helps create chemical adhesion with the following layers of the nail coating (gel, color, base). Removing the sticky layer weakens chemical adhesion and may increase the risk of lifting.

9. Level the nail with Builder Gel. When leveling, leave a 0.5–1 mm gap from the cuticle. Cure in the lamp for 60 seconds.

10. File and refine the nail shape after leveling. This creates sufficient thickness at the edge of the nail to support the free edge.

11. If the natural nail was thin, it may curl. Therefore, it is essential to file approximately 1 mm of the natural nail from the underside. This helps prevent lifting of the material. If the material is hard while the natural nail is very soft, the natural nail itself may begin to separate from the hard material at the free edge.

12. After filing, remove the sticky layer and cover the nail with gel polish.

13. Apply top coat and cure for 120 seconds. After curing, do not wipe the surface with any product, as this may reduce the shine.

CLASSIC NAIL EXTENSION

1. Removal.

2. Shorten the natural nail to approximately 1 mm and create a round shape.

3. Using a 220-grit file, gently file the surface of the nail without applying strong pressure, lifting the layers of the nail plate. Alternatively, use a 100-grit buffer.

4. Perform the manicure.

5. If removers are used, wash your hands with soap and water after working with them.

6. Degrease the nail using Nail Prep. Apply it in two stages. Use 4 wipes for this process (1 wipe for 5 fingers).
First stage: wipe the nail surface.
Second stage: place a wipe around an orange wood stick and carefully clean the cuticle area and sidewalls.

7. Apply primer.

8. It is best to apply the Rubber Base foundation layer with a flat gel brush. Apply the base evenly, carefully working into all sidewalls, and cure in the lamp for 60 seconds.

9. We recommend not removing the sticky layer from the base, as it helps create chemical adhesion with the following layers of the nail coating (gel, color, base). Removing the sticky layer weakens chemical adhesion and may increase the risk of lifting.

10. Place the nail extension form to create the free edge.

11. Build the shape of the artificial nail with Builder Gel. Cure for 30 seconds.

12. File the free edge and create the desired nail shape.

13. Remove the sticky layer and excess dust.

14. Apply another layer of Rubber Base over the areas where the file was used. Cure for 30 seconds.

15. Level the nail with Builder Gel, place it in the lamp and pinch the arch at 10–15 seconds. If the gel has a strong sticky layer, pinch at 20 seconds.

16. Complete the curing process in the lamp for 120 seconds.

17. Remove the sticky layer before applying gel polish.

18. Apply top coat and cure for 120 seconds. After curing, do not wipe the surface with any product, as this may reduce the shine.

Ingredients

Acrylates Copolymer, Hema, Silica Dimethyl Silylate, Dimethicone, Ethyl Trimethylbenzoyl Phenylphosphinate

May contain: CI 77891, CI 18965, CI 15510, CI 73360, CI 73385, CI 74160, CI 74260, CI 77266

TPO FREE

Product photos on the website may differ from the actual product.